[. . . ] PC/104-PLUS Module Model Number MB-73030 AMD Geode LX800 Low Power PC/104+ SBC with VGA/LCD, two 10/100LAN, Audio & SSD User's Manual Version 1. 0 1 Table of Contents Chapter 1. General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4. Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5. Board Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The following screen appears: 2 Use the arrow keys to move between fields. 3 The default space is available and optimized per the current onboard devices settings. Be very careful when change anything here. LPC Card Devices Configuration: Use the LPC Card Devices Configuration as follows: 1. LPC Card Devices Configuration" from the Motherboard Device st Configuration menu. The following screen appears: This page is to configure the 1 LPC UART device. Some fields let you enter numeric values directly. 26 Serial Port 1/2: to select port address & IRQ, the options are 3f8 IRQ4/ 2f8 IRQ3 Serial Port 2: IR Function Mode: Standard mode/ IrDA mode/ ASKIr mode IR I/O Pin Location Select: SINB/ SOUTB or IRRX/ IRTX IR Duplex Function Select: Full Duplex/ Half Duplex Parallel Port: 0378/ 0278/ 03BC/ Disabled Mode: Compatible/ PS/2 Bi-Direction/ EP1. 7/ EP1. 9/ ECP IRQ: IRQ7/ Disabled DMA: None/ Channel 3/ Channel 1 Console Redirection Configuration Console Output Setting: Disabled/ Enabled Baud Rate Setting: / 115200 After boot Enable or Disable Console ReDirection Agent after boot: Disabled/ Enabled 27 Use the Video and Flat Panel Configuration as follows: 1 Choose "F. Video and Flat Panel Configuration" from the Motherboard Device Configuration menu. The following screen appears: 2 Use the arrow keys to move between fields. Some fields let you enter numeric values directly. Internal Adaptor Mode: This is to choose the Internal Video controller mode when an external Video device is present. The options are: Primary/ Secondary/ Disabled Graphics Memory: to decide share video memory 2~254MB Driver controls init: Disabled/ Enabled, set Enabled when you want to use OS driver for Graphic Initialization. Output Display: Panel and CRT/ CRT/ Panel DOTPLL Bypass: Disabled/ Enabled, Use the frequency on DOTREF pin as dot clock frequency Flat Panel Configuration Type: TFT/ LVDS/ Auto ( auto detect the LCD type) Resolution: 320x240/ 640x480/ 800x600/ 1024x768/ 1152x864/ 1280x1024/ 1600x1200 Data Bus Type: 924 bits, 1 ppc/ 18, 24 bits, 2 ppc Refresh Rate: 60/ 70/ 72/ 75/ 85/ 90/ 100 Hz HSYNC Polarity: Active low/ Active high VSYNC Polarity: Active low/ Active high LP Active Period: Free running/ Active only SHFCLK Active Period: Free running/ Active only Software Backlight Control: Disabled/ Enabled Initial Brightness: Last value/ 0~100% 28 PCI Configuration: Use the PCI Configuration as follows: Choose "G. PCI Configuration" from the Motherboard Device Configuration menu. The following screen appears: Use the arrow keys to move between fields. Some fields let you enter numeric values directly. PCI Interrupt Steering: Enable/ Disable INTA# to IRQ Steering There is no PCI expansion slot available in this model, so there is no function here. USB 2. 0 Settings: OHCI: Enabled/ Disabled EHCI: Enables/ Disabled UDC: Disabled/ Enabled Over-current reporting: Disabled/ Enabled Use the Thermal Configuration as follows: 1 Choose "T. Thermal Configuration" from the Motherboard Device Configuration menu. The following screen appears: 2 Press <Enter> key here, it will read back the current temperature (Celsius) from System Monitor chip W83627HG and show. 29 2. Cache Enable: Enabled/ Disabled Cache Mode: Write-Back/ Write-Through L2 Cache Enable: Enabled/ Disabled Cache Allocate: Disabled/ DIMM 0 Memory Optimization DIMM0: Auto/ Manual CAS Latency: Auto/ 1. 5/ 2/ 2. 5/ 3/ 3. 5 CLK Refresh Rate: Auto/ 1. 5/ 3/ 7/ 31/ 62/ 125 uSec. Suggest keep at default Auto here 30 3-6 System Clock/ PLL Configuration. Use the System Clock/ PLL Configuration option as follows: 1 Choose "E. The following 2 Move between items and select values by using the arrow keys. Modify the selected fields using the +/- or <Enter> keys. Clock Mode Clock Determined By: H/W Strapping or Manual If Choose Manual, Manual PLL Settings CPU Multiplier: 1~32(default 15) *. 33. 3MHz x GeodeLink Multiplier = GeodeLink Speed Note: Strongly suggest no change here as it might cause the system not stable. 3. 7 Power Management Setup The Power Management Setup controls the board's "green" features. [. . . ] Press the <Y> key and then press <Enter> if you want to load the BIOS default. 3. 11 Load Optimized Defaults This option loads optimized settings stored in the BIOS ROM. The auto-configured settings do not affect the Standard CMOS Setup screen. To use this feature, highlight it on the main screen and press <Enter>. A line will appear on the screen asking if you want to load the Optimized Default Values. [. . . ]